Thursday, October 31, 2019
Neo-Polizeiwissenschaft Definition Essay Example | Topics and Well Written Essays - 1250 words
Neo-Polizeiwissenschaft Definition - Essay Example Complete metamorphosis of Neo- Polizeiwissenschaft of the 21st century is because of the risk attached to modernity; every society changing its set up to incline with modernism, and the security installation devices mounted everywhere ventilates the subject ââ¬Å"risk society.â⬠In the United States, scrutiny to mobile handset, email, and other new forms of communication (new media) project to new forms of social control. Information is encrypted to avert risk or the documents having information to fall into wrong hands. This is through copyright act; other forms that inform the adoption of Neo-Polizeiwissenschaft are identity thieves, the modern war systems, and corporate relations (Dennis Par.2). However, the new forms of social control are similar to Polizeiwissenschaft and differ only on mechanization of work, but similar in fixations. 1.2 Polizeiwissenschaft of the 21st century exchanges was what defined how societies related. There existed mutual relations; however, neo-P olizeiwissenschaft has adopted a secular identity. ... This places individuals in risk society; they are vulnerable to other forms of inclusion. The latter may result to employing Polizeiwissenschaft of the 21st century, such as the debt counseling and restructuring services, which are other social control models. Neo- polizeiwisssenschaft is thus the root cause of falsehoods and poor heuristic methods of understanding an individual before excluding him or her from such benefits. This is a clear manifestation of acceptability of 21st century models of social control. Neo-Polizeiwissenschaft is imitation of 21st methods of social control. It is a total risk when the new forms focus on extraction of capital and individualsââ¬â¢ importance are viewed as those that favor multinationals (Dennis Par. 39). Identity theft and the production of everyday fear is a feature in the new form of social control. Personal information displayed in the Neo-Polizeiwissenschaft i.e. emails is a risk and it is enough to lead to fear regarding personal secu rity. Personal information unlike 21st century Polizeiwissenschaft is no longer safe (Dennis Par. 44). The adoption of non-secularization has eroded the ethical considerations in handling personal information . Surveillance in public schools, in the U.S. and the U.K. has taken course by imposing license on personal information to oust infringement (Dennis Par. 46). However, the 21st century social control models aimed at taming such actions only display the continued risk creating fear because of tolerating illegal activities. The adoption strategies of social control i.e. personal replication of information in a digitized format is a reassurance of continued fear, as this can lead to external attacks
Tuesday, October 29, 2019
Comunity Pharmacy Practice Experience Assignment
Comunity Pharmacy Practice Experience - Assignment Example Having learned in class that this is the most important part in pharmacy work, I approached it with some fear and apprehension. The Manager, Cashier Meg and the other Staff were very encouraging, comforting and supportive. As I obtained the prescription and confronted the computer, I was relieved to know that the NexGen Computer System was easy to use. I went through the entire process of the Data Base Searching- Name of the Patient, Prescriber Search, Medication Search; clicking the appropriate information; and finally, printing the label. Determining the appropriate information and clicking it became easy because of my prior knowledge of medical terminologies, an exposure gained from POP 1-3 Classes; and, Methodologies in Patient Communication and Information Data Collection, as discussed in POP 6 Class. The handouts or materials distributed in POP 6 Class on the Legal Requirements of Prescription, Profile and Label; Ohio State Manner of Issuance of a Prescription; and, Labeling of Drugs Dispensed on Prescription really was a great help. The use of the computer and a computer system made the entire process very easy, fast and fun. The least enjoyable and most boring part of the Internship was the re-counting of tablets or pills, bagging, shelving and doing the inventory. I kept on thinking that I can do other things that were more important. Now, looking back I realize that I was doing an important task. I was being part of the team. If I didnââ¬â¢t do the work well, the pharmacy would suffer. I also realized that the tasks of making the inventory; and, shelving or returning medicine bottles to its proper shelves was only boring because I was already familiar with the generic and brand names. Knowledge I learned through the Listing of the Top Medicines distributed in Classes of POP 4-6. As to the re-counting of controlled medications before bagging; I had no difficulty identifying the controlled medications as I
Sunday, October 27, 2019
Gas metal arc welding
Gas metal arc welding Gas Metal Arc Welding (GMAW) 1 Introduction Welding is the fabrication process of joining two metal pieces permanently by applying heat or pressure or both. Joining takes place by melting and fusing: melting the base metals and applying the filler metal. This is achieved by melting workpieces and adding a filler material to form a pool of molten material (weld pool) that cools to become a strong joint. (Wikipedia) Some advantages of welding are that it produces a strong and tight joining between two pieces, is cost effective, simple and can be mechanized and automated. However welding results in internal stresses, distortions and changes in microstructure in the weld region. GMAW is currently one of the most popular welding methods, especially in industrial environments because it has lead to simplification of the welding process. GMAW is said to be one of the easiest welding processes to learn and perform. This is because in the process, the power source virtually does all the work by adjusting welding parameters to handle differing conditions. GMAW is extensively used in sheet metal industry and automobile industry. It has replaced riveting and resistance spot welding. It has also found applications in robot welding, where robots handle the workpieces and the welding gun to increase the consistency and the manufacturing process rate. The change in welding trends from SMAW to GMAW in the small and medium fabrications, mainly in the automotive industry. The reason is the attempt of manufacturers to maintain quality and decreasing cost.Lateron it was noted that GMAW was not preferred previously because of the limitation of incomplete fusion, which was not preferred for bridge and structural fabrications. However, with increase in the technology in GMAW, such as advancement in pulsed spray mode of transfer of metal, applications of the welding process has increased. Then there were some advancement in pulse metal arc welding by producing spray transfer at low mean currents. In a GMAW, process good thermal and electrical conductivities act as a drawback because such properties lead to excessive heating of base metals. Hence, limiting the use of the gas metal arc welding process. Pulsed gas metal arc welding (GMAW-P) addresses such problems. Another advancement in GMAW is the use of double electrode in the welding proc ess to increase the manufacturing speed. The DE-GMAW allows increasing the melting current while controlling the base metal current at a desired level. They also developed a model to correlate the change in resistance in the base metal required to achieve the desired base metal current. Then came upon the process of laser hybrid welding, which is popular in automotive industry today. They describe the interaction of laser with GMAW during welding and discuss various variables involved during the process. Later on engineers reviewed the droplet transfer models of solid wire. They described the simulation models: SFBT (static force balance theory), PIT (pinch instability theory) and VOF theory. They concluded that results produced by VOF were in confirmation with the experimental results. With advancement in technology of GMAW, its applications have touched new horizon. Therefore, it is important to study about this process in detail. The purpose of this report is to present the process variables, effect of process variables and equipment on the welding process, and sensing and control systems. Advantages, disadvantages and applications of GMAW process are briefly discussed. This report is expected to help future researchers in their research endeavors by acting as a literature review and a guide to the gas metal arc welding process. 2 Methodology This section will briefly describe the types of welding processes and then concentrate on the GMAW process. Different methods of GMAW process, the modes of metal transfer are introduced in this section. Emphasis is laid on the process variables in the GMAW process, equipment used, and the sensing and control systems. In designing a welding process, the effect of different process variables must be considered. Each application has its unique requirements and limitations. These will be in relation to the parameters that can be controlled or not. Also, the equipment used is of great concern in terms of its simple operation and control and uses. It is important to know the process variables that will have affect on the welding process and their relationship with other parameters. The emerging necessity of the welding processes is its automation. With the use of robots in welding, it has become necessary to automate the whole process and monitor and control the operation and quality of weld. Different sensing and control systems under research and recently introduced in the industry are discussed. 2.1 Welding processes Various welding processes have been developed and used in the welding industry depending upon their application, energy source, such as mechanical, electrical, chemical or optical, metals to be welded, location of metals, cost, etc. The three broad classes are: Solid state welding Fusion welding Soldering and Brazing 2.1.1 Solid state welding Solid state weldingis a welding process, in which two work pieces are joined under a pressure providing an intimate contact between them and at a temperature essentially below the melting point of the parent material (Kopeliovich). Two materials bind by diffusion of the interface atoms. The processes that come under this class are: Forge Welding (FOW) Cold Welding (CW) Friction Welding (FRW) Explosive Welding (EXW) Diffusion Welding (DFW) Ultrasonic Welding (USW) Although these processes have advantages, they require thorough surface preparation like degreasing, oxide removal and brushing or sanding. In addition, these processes are expensive. 2.1.2 Soldering and brazin. Soldering and brazing involve melting the filler metal, which then flows into the space between the closely fitted base metals and solidifies. In soldering, the melting point of the filler metal is below 800à °F while in brazing it is above this temperature. In both these processes, the melting point of the filler metal is below that of base metals. The filler metal is distributed between the properly fitted parts by capillary attraction. Some disadvantages are removal of flux residuals to prevent corrosion, no gas shielding may cause porosity of the joint, large sections cannot be joined, filler materials may contain toxic components and expensive filler materials. 2.1.3 Fusion welding Fusion welding involves the partial melting of two members welded by a heat source and amalgamated into one piece. The thermal energy required for fusion is usually supplied by chemical or electrical means. It may use a filler material like a consumable electrode or a wire. Fusion welding uses a protective layer like gas shielding or flux, which melts and forms a viscous slag on the weld metal that solidifies and removed later. 2.2. Gas metal arc welding (GMAW) Gas metal arc welding (GMAW) or metal inert gas (MIG) welding or metal active gas (MAG) welding is a semi-automatic or automatic arc welding process, which joins metals by heating them to their melting point with an electric arc. A continuous, consumable electrode wire and a shielding gas are fed through a welding gun. MIG involves use of an inert gas while MAG uses active gas like oxygen or carbon dioxide. 2.2.1 GMAW process Gas metal arc welding process usually comprise of a constant voltage, direct current (constant current or alternating current systems can also be used) arc burning between a thin bare metal wire electrode and the work piece. The arc and weld area are encased in a protective gas shield, fed through the welding gun. A continuous, consumable wire electrode is fed from a spool, through the welding torch/gun, which is connected to the positive terminal into the weld zone. 2.2.1.1 Parameters. The parameters of GMAW process are: Shielding gas Electrode size Electric parameter: voltage and current (continuous current is used) Feed rate (of electrode) Travel speed The shielding gas like carbon dioxide or a mixture of carbon dioxide and argon helps protect the molten metal from reacting with the atmosphere. Molten metal when exposed reacts with oxygen, nitrogen and hydrogen in the environment. Shielding gas flows through the gun and cable assembly and out of the gun nozzle with the welding wire to shield and protect the molten weld pool. The risk of reacting of metal with atmosphere limits the use of GMAW indoors because outdoors wind can blow the shielding gas away from the work piece and result in reaction. The consumable wire commonly is copper colored mild steel, which has been electroplated with a thin layer of copper to protect it from rusting, improve electrical conductivity, increase contact tip life, and improve arc performance. 2.2.2 GMAW methods. GMAW can be performed in three different ways: Semiautomatic Welding wire feeding is controlled by the equipment and the movement of welding gun is by hand. Also called hand-held welding. Machine Welding a gun is connected to a manipulator (not hand-held). Manipulator controls are adjusted constantly by an operator. Automatic Welding welds without the constant adjusting of controls by a welder or operator. 2.2.3 Mode of metal transfer in GMAW. GMAW use four different modes to transfer metal from the electrode to the work piece. These are: Globular mode of transfer Short-circuit transfer Globular transfer Spray transfer Pulse-spray transfer 2.2.3.1 Short-circuit transfer Short circuit transfer refers to the welding achieved by short-circuiting (touching) welding wire with the base metal between 90 200 times per second. The wire feed speeds, voltages, and deposition rates are usually lower than with other types of metal transfer such as spray transfer. This facilitates welding thin or thick metals in any position. A typical Short Circuit Cycle can be summarized in following steps: Electrode is short-circuited to base metal. No arc and current is flowing through electrode wire and base metal. Resistance in electrode wire increases causing it to heat, melt and neck down. Electrode wire separates from weld puddle, creating an arc. Small portion of electrode wire is deposited, which forms a weld puddle. Arc length and load voltage are at maximum. Heat of arc flattens the puddle and increases the diameter tip of electrode. Wire feed speed overcomes heat of arc and wire approaches base metal again. Short circuit cycle starts again. 2.2.3.2 Globular Transfer Globular transfer refers to the state of transfer between short-circuiting and spray arc transfer. Large globs of wire are expelled from the end of the electrode wire and allowed to enter the weld puddle. This type of mode of transfer results when welding parameters such as voltage, amperage and wire feed speed is somewhat higher than the settings for short circuit transfer. 2.2.3.3 Spray Arc Transfer Spray arc transfer refers to spraying a stream of tiny molten droplets across the arc, from the electrode wire to the base metal. Spray arc transfer uses relatively high voltage, wire feed speed and amperage values, compared to short circuit transfer. Inert argon rich shielding gas is used for best results. 2.2.3.4 Pulse-spray Transfer In the pulse-spray transfer mode, the power supply is made to cycle between a high spray transfer current and a low background current. It is different from the spray transfer in that it allows the super cooling of the weld pool during background cycle. In each cycle one droplet transfers from the electrode to the weld pool. The low background current allows pulse-spray mode of transfer to weld out of position on thick sections with higher energy than the short-circuit transfer, thus producing a higher average current and improved sidewall fusion. It can be used to lower heat input and reduce distortion when high travel speeds are not needed or cannot be achieved because of equipment or throughput limitations. 2.2.4 Process Variables The process variables of the GMAW affect the welding efficiency and weld quality. These variables either act alone by affecting the final product or they interact with each other and affect weld penetration, bead geometry. It is important to study these variables and have their set limits for a desired welding process and good overall weld quality. The enough penetration, high heating rate and rightwelding profile make the quality of welding joint. These are affected by welding current, arc voltage,welding speed and protective gas parameters. Table 1 shows the effect of different process variables on penetration depth, deposition rate, bead size and bead width. Table 1: Effect of process variables on penetration, deposition rate, bead size and bead width. Welding variables Desired changes to change Penetration Deposition rate Bead size Bead width Increase Decrease Increase Decrease Increase Decrease Increase Decrease Current and wire feed speed Increase Decrease Increase Decrease Increase Decrease Little effect Little effect Voltage No effect No effect Little effect Little effect Little effect Little effect Increase Decrease Travel speed No effect No effect Little effect Little effect Decrease Increase Decrease Increase Electrode extension Decrease Increase Increasea Decreasea Increase Decrease Decrease Increase Wire diameter Decrease Increase Decrease Increase Little effect Little effect Little effect Little effect Shield gas % Increase Decrease Little effect Little effect Little effect Little effect Increase Decrease Gun angle Drag Push Little effect Little effect Little effect Little effect Push Drag a change will occur if current is maintained by wire feed speed. http://products.asminternational.org/hbk/index.jsp The process variables are listed and discussed below: Welding current (electrode feed speed) Polarity Arc voltage (arc length) Travel speed Electrode extension Electrode orientation (gun angle) Electrode diameter 2.2.4.1 Welding current Welding current is the electrical amperage in the power system as the weld is being made. In GMAW constant voltage power sources (voltage) are used, therefore, amperage is thought to be controlled by wire feed speed. Welding current is read from the power source meter or a separate ammeter is often used. The total welding amperage or current supplied to the arc is determined by the wire feed rate, open circuit voltage setting and the slope setting on the welding power source (Figure 1 and Figure 2). The faster the wire feed speed, higher is the welding amperage. However, the wire feed speed only determines the balance between the welding current and the load voltage at the arc. When all other variables are held constant, an increase in welding current results in an increase in the depth and width of penetration, deposition rate, and weld bead size. This makes GMAW arc was made self-regulating. i.e. if the welder pulls the torch away from the workpieceââ¬âraising the arc length and arc voltageââ¬âthe power supply drops the arc current to burn off wire at a slower rate until the preset arc voltage was re-established. If the welder pushed the torch toward the workââ¬âshortening the arc and reducing the arc voltageââ¬âthe power supply quickly raised the welding current to burn off more wire until the preset arc voltage was re-established. 2.2.4.2 Polarity Polarity describes the electrical connection of the electrode (welding gun) with the terminal of a power source. When the gun power lead is connected to the positive terminal, the polarity is designated as direct current electrode positive (DCEP). When the electrode or the gun power is connected to the negative terminal, the polarity is designated as direct current electrode negative (DCEN). When alternating current (AC) is used, the polarity changes every half cycle of 50 or 60 Hz. In GMAW usually DCEP is used because it yields a stable arc, smooth metal transfer, relatively low spatter, good weld bead characteristics and deep penetration for a wide range of welding currents. On the other hand, DCEN results in the molten droplet size tends to increase and the droplet transfer becomes irregular (Figure 3). This increases large grain spatter. Some wires with unique chemical composition have been developed for DCEN, which give excellent results on galvanized sheets. Variable polarity gas metal arc welding (VP-GMAW) is the current trend in the welding industry. Inverter pulse power supplies allow to combine DCEP and DCEN polarities in varying amounts (Figure 4). In their research, Harwig et al. (2000) showed that VP-GMAW could be used for welding thin gage aluminium sheets. They noted that during DCEN polarity, droplet formation takes place and it is transferred across the arc by DCEP polarity. They said that DCEN could be added up to 60 % to the current, beyond that the arc becomes unstable. 2.2.4.3. Arc Voltage Arc voltage is the amount of voltage present between the electrode and workpiece. Arc voltage and arc length are used interchangeably. Arc voltage is an approximate means of defining the physical arc length in electrical terms. However, one physical arc length could yield different arc voltage readings, depending on factors such as shielding gas, current, and electrode extension. If all these variables are kept constant, arc voltage and arc length can be correlated i.e. with increase in voltage setting, arc length increases. The welders are interested in arc length, but arc voltage is easy to monitor and must be specified in welding procedures. Therefore, its the arc voltage that is most commonly used term than the arc length. Arc voltage controls the height and width of the weld. Any increase in arc voltage from specific value, flattens the bead and increase the width of the fusion zone. Very high voltage results in porosity, spatter (unstable arc), and undercut. However, a voltage less than required will result in narrower weld bead with higher crown i.e. wire stubs on the work. Therefore, voltage must be set midway between high/low voltages. 2.2.4.4. Travel speed is the speed at which a welder moves the electrode along the joint to make a weld. Technically its the linear rate at which the arc is moved along the weld joint. Weld penetration is always maximum at intermediate travel speed, when all other conditions are constant. If low travel speed is used, the arc will impinge on the molten weld pool than working on the base metal and hence affect penetration efficiency. Large increase in travel speed will result in less thermal energy on the base metal. At high speed, the rate of melting of base metal is increased first and then decreased. If travel speed is increased any further, undercutting along the edges of weld bead may occur because of insufficient deposition of filler metal in the path melted by the arc. High speed GMAW as signifies uses high travel speeds. Rapid Arc Company uses pulsed GMAW for faster travel speeds, low spatter, out of position operation and lower heat input. They achieve high travel speeds by using lower arc voltage i.e. shorter arc length, this reduces spatter and washed out bead profile, allowing high torch travel speed. They divided rapid waveform into four parts (Figure 5): Pulse: A sudden increase in current increases arc energy, and forms and squeezes a molten droplet extending from the end of the electrode. Puddle Rise: The ramp down of current relaxes the plasma force, depressing the puddle, allowing it to rise up towards the droplet. Short : The arc collapses, and the droplet contacts the weld puddle. Puddle Repulsion: immediately following a short breaking into an arc, a gentle plasma boost pushes the puddle away and conditions the electrode tip. This ensures reliable separation of the wire tip and the puddle resulting in a stable rhythm of the cycle. 2.2.4.5 Electrode orientation Electrode orientation is the angle of the electrode axis with respect to the travel direction. This is called the travel angle. On the other hand, it could be the angle of the electrode axis with the work surface. This is called the work angle. When the electrode points in a direction opposite to the travel direction, it results in a trail angle and is called the backhand welding technique. When the electrode points in the direction of travel, it results in a lead angle and is called the forehand welding technique. The maximum penetration is achieved for trailing travel angle between 5 to 15à ° (from perpendicular). This also provides a narrow, convex surface configuration and shielding of the molten weld pool. However, the leading travel angle provides the welder better visibility and a flatter weld surface. This is more commonly used technique. For materials such as aluminum, a leading angle is preferred, because it provides a cleaning action ahead of the molten weld metal, which promotes wetting and reduces base-material oxidation. This is because the leading angle of the electrode pushes the molten metal and slag ahead of the weld. When producing fillet welds in the horizontal position, the work angle should be about 45à ° to the vertical member. 2.2.4.6. The electrode extension The distance between the last point of electrical contact (usually the gun contact tip or tube) and the end of the electrode. An increase in the amount of this extension causes an increase in electrical resistance. This, in turn, generates additional heat in the electrode, which contributes to greater electrode melting rates. Without an increase in arc voltage, the additional metal will be deposited as a narrow, high-crowned weld bead. The optimum electrode extension generally ranges from 6.4 to 13 mm for short-circuiting transfer and from 13 to 25 mm for spray and globular transfers. 2.2.4.7. The electrode diameter Influences the weld bead configuration. A larger electrode requires a higher minimum current than a smaller electrode does to achieve the same metal transfer characteristics.Higher currents, in turn, produce additional electrode melting and larger, more-fluid weld deposits. Higher currents also result in higher deposition rates and greater penetration, but may prevent the use of some electrodes in the vertical and overhead positions. 2.2.5 Equipment The basic assembly of GMAW containing the components of equipment can be seen in Figure 6. It is important to study each part of the equipment to reach the required quality of the weld. Each application of GMAW will have a specific requirement for each part. Therefore, these can be controlled or modified to change the welding process to achieve good welding efficiency and quality. The fundamental equipment for a typical GMAW installation includes: Welding gun Electrode feed unit Welding control mechanism Power source Electrode source Regulated Shielding gas For automatic welding equipment the wire feed unit and the current contact and gas barrel are combined in a single welding head (Figure 7). For Semi automatic welding flexibility is generally achieved by separating the wire feed unit from the torch and passing wire, gas, current and cooling water through the flexible conduit. Wire-feeding complexities must be considered using these systems. High powered motors are required to push wire for several yards. Ferrous metal wires can be fed through smooth, flexible and rigid spiral steel wire-feed tubes. But, aluminium and non-ferrous metals are difficult to feed through tubes until they are nylon lined. The wire feed difficulties increase with decreasing wire diameter. Welding current in GMAW equipment is introduced to the wire by passing it to a copper tube. A variation in point of current pick up can alter the resistance between contact and arc and cause variations in burn-off rate because of its effect on overall circuit resistance. With high currents or high resistance metals the current contact tube is shortened or fitted with small tip diameter tip to reduce variation. Water cooking is required for equipments that have automatic welding heads and those that work at about 250 A. Water cooling and chromium-plated surface make removal of fume and spatter from the nozzle easier. POWER CABLE (NEGATIVE) POWER CABLE (POSITIVE) WELDING VOLTAGE CURRENT DETECTION 115 VAC IN TO PRIMARY POWER 230/460/575 V COOLING WATER IN SHIELDING GAS IN TO CARRIAGE DRIVE MOTOR 115 VAC IN TRAVEL START/STOP WIRE FEED MOTOR SHIELDING GAS IN COOLING WATER IN COOLING WATER OUT The parts of GMAW are discussed below in detail. 2.2.5.1Welding gun Responsible for delivering the electrical current to the electrode, and directs it to the work piece and allows the flow of shielding gas to the weld area. The choice of welding gun is critical, but often ignored over power source, wire feeder, and shielding gas, which are most costly. Proper choice can give good welds and productivity. Different types of guns are used for different applications: heavy duty guns for high current and high volume production, and light guns for low current and out of position welding. Figure 8 shows the most commonly used gun, which is air cooled. Water cooled gun is used for high current requirement. Welding guns are rated on their current-carrying capacity. If inert gas is used, the gun rating is reduced to a much lower extent. A welding gun can be equipped with its own electrode feed unit. Parts of welding gun Back end is the power pin that connects the gun and power cable to the wire feeder. This connection must be tight. A loose connection between the gun and the feeder can cause electrical resistance throughout the entire system. This will result in overheating, which may damage the gun or the wire feeder. This may also cause gas leakage and poor conductivity that can lead to an erratic arc and poor weld quality. Usually a supportive strain relief is provided at the connection between the power cable and wire feeder. This helps in good wire feeding, which results in a stable arc and quality welds. There is another option of selecting a gun with multiple feeders for various GMAW applications reducing overall cost. Contact tube: is used to transmit welding current to the electrode and to direct the electrode towards the work. It is usually made of copper or a copper alloy and connected electrically by power cable to the power source. The tube hole for wire input is of 0.13 to 0.25 mm larger than the wire being use, larger for aluminium and non ferrous metals. Nylon lining is used for non ferrous metals and aluminium electrodes. This inner surface of the tube has to be changed in case of excessive wear, which may result in poor electrical contact. Consumables (nozzles and tips): The nozzle in the welding gun directs the shielding gas into the welding area. An even flow must be maintained to protect molten weld from the environmental gases. Larger nozzles are used for high current work with large weld pool and small nozzles used for low current work. Consumables are selected based on longevity instead of price. This reduces costs of replacement parts and changeover time. Non-threaded, large-base contact tips that fit securely to the diffuser provide good electrical conductivity and heat transfer. It is important to use heavy-duty tips and nozzles that provide good gas coverage to help ensure good arc starts, less spatter, and less rework and cleanup. Electrode conduit and liner support: protect and direct the electrode from the feed rolls to the gun and contact tube. They are connected to a bracket adjacent to the feed rolls on the electrode feed motor. It is necessary to maintain uninterrupted electrode feeding for good arc stability. The liner is the most critical component of the GMAW gun because of the problems that can arise from it. A steel liner is used for steel and copper electrodes, whereas nylo
Friday, October 25, 2019
Putting A Price on Students :: essays research papers
Putting A Price On Students Summaryà à à à à The state has taken on the obligation of providing budget funds for the education of each individual student at an institute of higher learning if he or she has passed the unified state exam. Russia continues to experiment with its educational system. Five Russian regions used unified state exams last year. Two Russian regions decided to continue the experiment by introducing state-issued vouchers (GIFO) this year. Reformers who tend to modernize Russian education believe that both experiments are necessary to produce the right effect. If everything is more or less clear with the unified state exam, the GIFO is still a mysterious and unknown phenomenon. The only thing that is known about the GIFO is that it comes from the state budget. à à à à à The reasoning behind the vouchers is a better education chance for all. Now students will be able to control their debt which will be owed at the end of their matriculation. Educational Impactà à à à à The funding of Russian institutes of higher learning could, without exaggeration, be called equalizing. Today, each university or institute draws up an estimate according to which it receives its share of state funds. In doing so, no one takes into account the category of the particular institution, whether it is prestigious, strong or weak, what kind of experts and specialists it actually trains. In other words, there is no incentive to improve the quality of education. Fifty-one percent of first-year students who were admitted to institutions of higher learning last year had to pay for their education. Secondly, parents spend about one billion dollars to prepare their children for university exams and to ensure their admission to institutes and universities. Most of this money circulates in the shadow sector of the Russian education system. The Russian Education Ministry believes that this situation reveals the inefficiency of financing Russia n education. A state that increases spending on education, including higher education, could expect maximum efficiency and the best performance. Analysisà à à à à I support the idea of the GIFO because it seems to give every student an equal opportunity for education. But I wonder how many times can a student take the unified exam since your amount of state support depends on your score. And I also wonder if you can take the exam more than once will your support increase? The plans sound good on paper but I wonder if only the gifted or upwardly mobile students will be the only ones who are helped by these vouchers. Putting A Price on Students :: essays research papers Putting A Price On Students Summaryà à à à à The state has taken on the obligation of providing budget funds for the education of each individual student at an institute of higher learning if he or she has passed the unified state exam. Russia continues to experiment with its educational system. Five Russian regions used unified state exams last year. Two Russian regions decided to continue the experiment by introducing state-issued vouchers (GIFO) this year. Reformers who tend to modernize Russian education believe that both experiments are necessary to produce the right effect. If everything is more or less clear with the unified state exam, the GIFO is still a mysterious and unknown phenomenon. The only thing that is known about the GIFO is that it comes from the state budget. à à à à à The reasoning behind the vouchers is a better education chance for all. Now students will be able to control their debt which will be owed at the end of their matriculation. Educational Impactà à à à à The funding of Russian institutes of higher learning could, without exaggeration, be called equalizing. Today, each university or institute draws up an estimate according to which it receives its share of state funds. In doing so, no one takes into account the category of the particular institution, whether it is prestigious, strong or weak, what kind of experts and specialists it actually trains. In other words, there is no incentive to improve the quality of education. Fifty-one percent of first-year students who were admitted to institutions of higher learning last year had to pay for their education. Secondly, parents spend about one billion dollars to prepare their children for university exams and to ensure their admission to institutes and universities. Most of this money circulates in the shadow sector of the Russian education system. The Russian Education Ministry believes that this situation reveals the inefficiency of financing Russia n education. A state that increases spending on education, including higher education, could expect maximum efficiency and the best performance. Analysisà à à à à I support the idea of the GIFO because it seems to give every student an equal opportunity for education. But I wonder how many times can a student take the unified exam since your amount of state support depends on your score. And I also wonder if you can take the exam more than once will your support increase? The plans sound good on paper but I wonder if only the gifted or upwardly mobile students will be the only ones who are helped by these vouchers.
Thursday, October 24, 2019
Elementary School and Middle School Essay
Transitioning from elementary school to middle school is something we all have or had to do! Most kids cringe at the thought of making this huge step in life. For many students this transition can be a time of mixed emotions. Having been through this experience, I will compare and contrast the two, hoping that this will give you a clear picture of elementary and middle school. Elementary and middle school have distinguishable characteristics. In elementary schools, you basically have your homeroom teacher and one other teacher. The movement of students is very limited and you are mostly escorted by a teacher. Teachers are more understanding and are not as demanding because of the studentââ¬â¢s age. Fun days are set aside as an award for students that have done what is expected of them. Most of the children are placed in classroom with the same students each year. Elementary school is very important in our young studentââ¬â¢s lives; this is where it all starts. However, middle school students are expected to execute their daily tasks without assistance. Teachers are there to direct the students in right direction; everything else is left up to the student. Middle school students have several different classes, in each class it is usually a different teacher. Students have lockers to store their books and other supplies. In middle school students are required to be more independent and serious about school. Elementary school set the pace for all other levels of schooling. Students enter elementary school learning all the basic aspects of school system and the learning process. At this stage in life most students are eager to learn and get excited to learn new things. Elementary is the main point of delivery, it introduces social skills, behavioral adjustments, and basic academic learning. Middle school prepares students for higher education. Ultimately, middle school bridges the gap between elementary and high school. It is definitely a different experience than elementary, but it prepares students for their future and encourages them to be more independent. Elementary schools and middle schools also have common qualities. They are both open Monday through Friday on the same days. Each day students eat lunch at a designated time. All students are expected to sit in desks in an appropriate manner. Teachers require students to be respectful and display good behavior at all times. Homework is given on a daily basis and class discussions are routine also. School is essentially school with minor differences. Each school level has its own proââ¬â¢s and conââ¬â¢s, they are also very similar. They each have their own benefiting factors and they are used to their advantage. School systems up this way because it is initially what works in our culture. Elementary and middle schools are stepping stones that that help us get from one place to another in our academic life. Each level is an important standpoint for academic excellence and they should be taken seriously so that you can be an effective student/learner.
Wednesday, October 23, 2019
What is supply Management?
Several authors have offered various definitions of supply management, whereas the definitions have seemed concomitant, the functions of supply management have at times appeared paradoxical. According to Gattorna et al (2003), supply management is defined as the methodical business progression that encompasses diversified functions such as synchronizing inbound and internal logistics and managing inventory than legendary buying, this is in agreement with Baily et al, (2005), who implies that supply management is the recognition, acquirement, entree, position and administration of resources and associated competence the business needs or prospectively needs to survive. However, Leenders et al, (2001), defines supply management as techniques and procedures of institutional or corporate buying, and argues that supply management is concerned with the oversight and administration of services and resource inputs, handling the suppliers of the inputs and sustaining input acquisition process. These definitions have however centered on explaining supply management as just the process buying and the management of the processes of buying and related procedures. Trent , (2007), offers a diversified definition of supply management and argues that supply management has matured from deliberate function of procurement and purchasing into a crucial strategic role influencing the survival of the organizations, he argues that supply management plays a primary role in the organization in that it influences the organization's image, social and corporate policy, progresses the competitive position and customer satisfaction and promotes effectiveness, productivity and efficiency of an organization. Supply management is therefore viewed as the main source of strategic competitive advantage of an organization. The research shall therefore evaluate the defined effectiveness of strategic management as a source of competitive advantage to organizations.
Tuesday, October 22, 2019
Julieus Ceasar Essay
Julieus Ceasar Essay Julieus Ceasar Essay Both speakers are connecting to Caesar by trying to prove a way to make Caesar either stay home or got to work. One speaker is Calpurnia, she wants Caesar to stay at home, because she has a feeling that Caesar might die. The other speaker is Decius Brutus and he wants Caesar to go to work so that he and his friends can kill him. Both speakers have their own reasons that want to make Caesar want to stay but what Calpurnia said wasnââ¬â¢t enough so he was frightened. I think that Caesar would believe Brutus more because Brutus sounds more realistic than Calpurnia does. The words that Calpurnia uses in the passage are nervous because she doesnââ¬â¢t want anything to happen to her husband. She also uses the words I circled to try and convince Caesar not to go to work. On the other hand the words that Brutus uses are more persuasive because he twists the things Calpurnia says and make them seem positive. He also says things like that make Caesar want to go to work like when Brutus says, ââ¬Å"If Caesar hide himself, shall they not whisper, ââ¬ËLo, Caesar is afraidââ¬â¢?â⬠. This quote shows what people will think of Caesar is he listens to his wife and stays home. I believe that Brutus is more persuasive because he gives great examples. The examples that both passages give are okay, but some are better like when Calpurnia said that she had a bad dream about Caesarââ¬â¢s death. Calpurnia says, ââ¬Å"Your statue spouting blood in many pipesâ⬠. This quote shows that if Caesar goes to work and get crowned there will be bloodshed. Obviously the example that Calpurnia gave Caesar wasnââ¬â¢t enough to convince Caesar to stay home so he leaves his home and ran into Brutus, who convinced Caesar to go to work and get crowned. Decius Brutus says, ââ¬Å"If you shall send them word you will not come, their minds may changeâ⬠. This quote means that if Caesar doesnââ¬â¢t show up to get crowned, the crowd of people wonââ¬â¢t want him as king any more. In both of the passages the speakers both talk in a different point of view, Calpurnia speaks in first person, while Brutus talks in second person. Calpurnia speaks in first person because she is trying to get a point though Caesar in hopes to convince Caesar
Subscribe to:
Posts (Atom)